Steam Community :: Group :: [HUN] FullClip

cg_drawfps on

Enables the FPS counter, you'll see it in the top right corner of the screen. Use the same command and off to disable.

cg_drawfpsonly 1

Shows your in game FPS

com_maxfps X

Range = 1-1000

It can improve lag to set your max fps. If you are using VSync then set your maxfps to 60. Replace 'X' with a the number. Use '0' zero to unlock maxfps.

r_flameFX_fps 30

15 is default, LOW FIRE FPS FIX

cg_fov 80

FOV = Field of View, 65 is the default, 80 is a good value

drawlagometer 1

Shows the LAG-O-METER on your screen to see if you have a smooth connection or you are having connection problems, a smooth graph is good, unsmooth is not.

r_multiGpu

This should only be enabled if you have multiple graphics cards or a graphics card with multiple GPUs. If you don't have multiple GPUs, don't know what this means, or are having issues with your MultiGPU solution, please set this to "0".

r_multithreaded_device

This setting should be enabled for EVERYBODY as the minimum requirements for Black Ops clearly states that you need a multithreaded (multicore) CPU to run the game. However, some people have noticed that by setting this to "0" some of the skipping lag is relieved. Test this out only as a last resort.

r_vsync

VSync prevents screen tearing. If you don't know what that is, just set it to "0" because you probably don't care anyway. Otherwise, VSync usually doesn't have any negative performance issues with today's graphics cards. However, there may be a few performance issues linked to VSync with the current release of Black Ops. Try setting this to "0" for compatibility.

r_blur_allowed

This setting enables Blur shader effects. If you have a strong shader card, this setting may be negligible. Otherwise, just go ahead and set this to "0".

r_distortion

This setting enables Distortion shader effects. If you have a strong shader card, this setting may be negligible. Otherwise, just go ahead and set this to "0".

r_dof_enable

This setting enables Depth of Field shader effects. If you have a strong shader card, this setting may be negligible. Otherwise, just go ahead and set this to "0".

r_glow_allowed

This setting enables Glow (HDR?) shader effects. Normally, this should have a negligible performance impact. HOWEVER, this setting seems to be buggy! Performance improved DRAMATICALLY when I set this option to "0".

rate

Default = 25000

Rate is the rate at which the client sends packets to the server. If you set this too low, below 10000 or so, you run the risk of sending insufficient data to the server and lagging out. Set this too high, above 50000 or so, and you run the risk of flooding your connection to the server. This setting should be adjusted according to your connection speed and may take some fine tuning.

cl_maxpackets

Default = 100

This setting controls how many packets the client will hold to ensure packet transmission. If you set this setting to low, below 20 or so, then you run the risk of being disconnected prematurely.

If you set this setting too high, above 150 or so, then you run the risk of continually resending redundant data and lowering your ping (or worse, getting choked). This setting is very hard to tune because it depends on so many factors beyond your own connection.

Most people have found setting this to 100 is a good compromise for most servers.

Improve net play by setting this to 100 or half of your max fps

snaps 30

This is possibly the most important setting for getting a good connection.
Snaps setting determines how many updates you recieve from the server. 20 to 30 for
56K connects in quake series 40 for high speed internet im sure the same for cod. (30 is fine).

stoprecord (Used in console)

Rate up

Leave a comment

Showing 1 to 5 of 5 posts

Subscribe to RSS Feed